Home / server / Questions / 32543
Accepted
Clear.Cache
Asked: 2009-06-27 18:39:34 +0800 CST

64 bit Xen install, Network Issue

  • 772

I'm playing around with a test server, install Xen on a Centos 5 box.

http://www.howtoforge.org/paravirtua...tos-5.3-x86_64

I've tried two methods to create a vm.

virt-install

and

virt-install -x "ip=xxx.xxx.70.212 gateway=xxx.xxx.70.211 subnet=255.255.255.248"

If I do virt-install, it asks me this:

http://i40.tinypic.com/2m5c8ys.png

Automatic DHCP never works. If I try manual config, I have no idea what to put it. I did try this:

IPv4 address: xxx.xxx.70.212__ / 255.255.255.248_ Gateway: xxx.xxx.70.211___________________________ Name Server: _________________________________________

note: only here in my post am I actually putting "xxx" in the IP for privacy reasons only. The 70.212 is the main server IP that I ssh into.

See 2nd screenshot for error. Same thing with various valid mirrors I tried.

http://i40.tinypic.com/64fqyh.png

This is my ifcfg-eth0 info:

DEVICE=eth0 BOOTPROTO=static IPADDR=xxx.xxx.70.212 NETMASK=255.255.255.248 ONBOOT=yes TYPE=Ethernet

I've tried 2 different mirrors so far, same error.

http://wftp.tu-chemnitz.de/pub/linux/centos/5.3/os/x86_64 http://mirror.its.uidaho.edu/pub/centos/5/os/x86_64/

My resolvers are just fine too in /etc/resolv.conf

Note, I did not do anything at all. I had a fresh Centos 5 64bit install and then followed that Xen install guideline. That's it.

xen

2 Answers

  1. Best Answer

    I've been building 64-bit Xen hosts on Dell 2850 and 2950s without problem... Looking at your virt-install option though I believe you want netmask=x.x.x.x rather than subnet=x.x.x.x as that's the only difference I see directly off hand.

    If that is the only options to the command line you're using for virt-install you need to include a NIC using the -w option to add it to one or more of your Xen bridges. My typical call for virt-install is:

    virt-install -n <hostname> -r <memory> -p --os-type=linux --os-variant=rhel5 \
-f /dev/xenvg/<hostname> -l http://KS-REPO/redhat/linux/enterprise/5/en/os/i386 \
--vcpus=1 -w bridge:xenbr0 --nographics --noautoconsole \
-x "ks=http://KS-REPO/ks/KICKSTART.KS ip=x.x.x.x netmask=255.255.255.x \
gateway=x.x.x.x dns=PRI-DNS-IP,SEC-DNS-IP"

    In most cases I tend to have a 64-bit host but 32-bit guests... could modify to work with 64-bit guests if I needed to. This gives me 2 NICs (eth0 and eth1) attached to the xenbr0 and xenbr1 bridges respectively, single CPU guest installing a RHEL5 variant.

    • 1

  2. If you happen to have a Dell 2950 (or any other Dell x9xx using a Broadcom NetXtreme II) I suggest that you follow http://lists.xensource.com/archives/html/xen-users/2007-04/msg00629.html

    • 0