Home / server / Questions / 52236
Accepted
Geo
Asked: 2009-08-11 04:41:11 +0800 CST

Exim taking long time to send emails, how to decrease delay in Exim service?

  • 772

The linux server where exim service is running is under no load.

The system is sending email successfully but is taking a long time to send each email.

Basically if I telnet to localhost port 25 and then I try to send an email from there the response from the server is super slow. The mail application we have running there is taking more than 8 minutes to send 4 emails.

Has anyone confronted this issue before with EXIM and maybe you might now what is the setting that is making EXIM wait so long for something. I am looking at the logs and I cannot see anything indicative of an error. Below a sample of the mainlog:

2009-08-10 07:21:05 H=(aurl.domain.ni) [127.0.0.1] Warning: Sender rate 4.6 / 1h
2009-08-10 07:21:29 1MaTsX-0000mw-Oe <= [email protected] H=(aurl.domain.ni) [127.0.0.1] P=esmtp S=22003 [email protected]
2009-08-10 07:21:54 SMTP command timeout on connection from (domain.com) [127.0.0.1]
2009-08-10 07:22:42 1MaTsX-0000mw-Oe ** [email protected] R=lookuphost T=remote_smtp: SMTP error from remote mail server after RCPT TO:: host mx3.earthlink.net [209.86.93.228]: 550 [email protected] unknown
2009-08-10 07:22:42 1MaTti-0000nM-3b <= <> R=1MaTsX-0000mw-Oe U=mailnull P=local S=23089
2009-08-10 07:22:42 1MaTsX-0000mw-Oe Completed

linux email troubleshooting email-server exim

3 Answers

  1. DNS is a common issue, as jj33 suggested.

    Exim may be configured to do an ident lookup on incoming email. For a long time this defaulted to a 30 second timeout - I'm not sure if this is still the case. Delaying mail slightly helps a lot with spammers I've found (naive spammers will push the mail anyway, which then lets you trigger on protocol violation errors), so it's worth doing still IMO.

    # RFC1413 lookups can cause timeouts. (ident)
rfc1413_hosts = *
rfc1413_query_timeout = 5s

    rfc1413_hosts defaults to *, so if you want to disable it, try

    rfc1413_hosts =
    • 5
  2. Best Answer

    The server appears to be doing throttling which might affect you if you are testing from one IP:

    2009-08-10 07:21:05 H=(aurl.domain.ni) [127.0.0.1] Warning: Sender rate 4.6 / 1h

    Often issues like this are related to poor DNS. Exim does a lot of resolution during processing mail. Check the DNS config on the Exim server. Check the performance on the DNS server it is using.

    Is the server doing any DNSBL processing? I'm often asked to look at servers exhibiting poor performance and it turns out they are using DNSBLs that have been retired, meaning lookups are timing out.

    Try running exim in debug on the server to see where the problem is. The following will run an Exim daemon on port 26, staying attached to the console and printing lots of debug:

    exim -bd -d -oX 26

    Then telnet to tcp/26 instead of tcp/25 and test as you had been.

    • 3

  3. Mine was damn slow and after I deactivated a certain modifier (dnslists) in the vexim-acl-check-rcpt.conf file, my mails are now very fast in sending. Seems like the the modifier I was using is invalid though it came with the vexim package. Further investigation shows that the dnslist zen.spamhaus.org:list.dsbl.org seems to be invalid. So I deactivated it and worked fine too. Hope it helps someone else in a way. This is my vexim-acl-check-rcpt.conf file

    *# deny message = DNSBL listed at $dnslist_domain\n$dnslist_text

    dnslists = zen.spamhaus.org:list.dsbl.org

    deny message = DNSBL Blacklisted dnslists = list.dsbl.org deny message = DNSBL Blacklisted dnslists = dnsbl.sorbs.net deny message = DNSBL Blacklisted dnslists = rhsbl.sorbs.net deny message = DNSBL Blacklisted dnslists = bl.spamcop.net*

    • 0