I live and work in a building that is nearly 20 years old. My Internet connection is in the cellar along with my servers and has a nominal rating of 100 MBit. I have a gigabit switch in the cellar connecting everything up.
That gigabit switch has a direct ethernet connection to a second gigabit switch three storeys up in my office.
I have tested the speed of the connection from upstairs to the cellar and am getting about 80 Mbit, somewhat less than the nominal speed of my Internet connection. I could live with that, but it would be nice to have a faster connection to my servers, so I'd like a gigabit connection between the switches.
Inspection of the cable from the office to the cellar revealed that it is an ISO/IEC 11801. There is no room in the cable duct for a thicker cable (e.g. CAT6 etc.) because the duct also carries a TV cable.
It seems to me, therefore, that a good way forward would be to put in a duplex fibre optic cable between the two switches and interface it with a gigabit media converter at each end. Is it really as simple as that?
The thing I know I really don't understand is the cable confection. Can one simply cut fibre optic cable to length, and connect it to wall sockets and SC or LC connectors? I can't use ready-made cables because the connectors won't fit down the duct, I think.
If someone could point me at a "howto" or share their wisdom and experience with me, I'd be very grateful.
Steve
In theory it is as simple as you describe. The problem you will run into is that you need to join two pieces of fiber. In practice you have two options for this:
Also, getting the fiber in there will probably be a challenge. Fiber might be smaller and easier to bend, but it is also more fragile than cat 6.
My recommendation would be to ask your local fiber company to built it for you. They have specialized equipment to get fiber into complicated ducts, the equipment to splice it properly and will be able to provide you with a measurement protocol at the end that shows that the fiber actually works. Around here I would expect to pay perhaps $1000 for the job of running a fiber through an existing duct between floors, including pigtails at the end that are fixed in existing racks.
What exactly is the problem with your existing cable?
You list a cable standard that covers everything from cat1 to cat6a.
If your cables are true cat5 cables (ie you've got 8 wires and they're twisted together a certain times per foot) and you're less than 300 feet from end to end, you should be able to run gig ethernet over that link.
Let me repeat this. Cat5 support gig ethernet. If it can't support gig ethernet, it isn't cat5.
You should look into your existing wires are not performing up to spec. It may be as simple as re-terminating both ends carefully.
Borrow a decent cable tester and find out what's going on. Only then should you look into dumping lots of money into the project.
You may also consider yanking all the cables out of the conduit and running new cables. Buy a pre-terminated fiber and buy a new bit of TV cable and re-terminate that in the field. Use the old cable as a pull for the new cable. Just don't make a mistake...
I think you're going down the wrong track in your diagnostic.
But, no I'm not going to discourage you from putting in fibre yet. First, you need to clearly identify where the problem is.
First off, check the internet speed from your downstairs server with speedtest.net or similar.
If it's a windows server perhaps you can RDP to it and then do the speedtest. Make sure you do this when no one else is using the internet... like at night or early morning before all the workers come in.
Do you get 80Mbit/s average? If you do, then congratulations, that's the bottleneck for your so called 100Mbit/s internet connection (i.e. not the upstairs/downstairs link). By the way, if you're paying for 100Mbit, don't expect to get that. 100Mbit/s is theoretical maximum throughput. However, it doesn't take into account the protocol overheads and such like. In actual fact, within 80% of maximum is quite acceptable.
Secondly, have you tried some speed testing between your server in the basement and your PC upstairs? You should get around 600+Mbit/s... You are unlikely to get more than 750Mbit/s throughput. There are good reasons for that. Part of it is again, protocol overhead. Also PCI bus speed and so on. If on the other hand, you're getting much less than this, then I'd consider either putting in fibre, or a higher grade cable like CAT6 just because it's less prone to error at high speed and a little more shielded. If you know you've got power and other things running down this same duct then this could be a source of error. I believe there are testing tools for checking error rates.. maybe you can hire something?
But, if you want fibre, as others have mentioned I'd get a company that specializes in this to do it for you. You can terminate them yourself, but you need the right gear to do it, and probably a couple of attempts to get it right. It's not hard, although more work than copper and requires a lot more patience. As with all things we do ourselves, if we're not familiar it can take us 10 times longer than someone qualified.