The perfect server room?

• Enough space for expansion
• Plenty of network ports
• Sufficient network bandwidth
• Plenty of dedicated power sockets
• Should not be on the ground floor (risk of flooding + less secure)
• Fire suppression facilities + smoke alarms
• IP KVM for remote access
• Telephone (so the operator can call a support line while looking at the hardware)
• Pens + paper
• A label printer - label everything!
• A standard printer (nice to have)
• Spare network and power cables
• Air conditioning (also dehumidifies)
• Good UPS (with automated/controlled shutdown functionality)
• Sufficient power to run everything (and enough for expansion)
• Entrance security (preferably also with logging)
• Physical security (security on windows, entrance, etc.)
• Whiteboard (nice to have)
• Fireproof safe (for storing backup tapes, passwords and installation media)
• Good server racks - well maintained (cabling)
• Enough space to work comfortably behind the servers
• A table large enough to build/dismantle a server on (plus monitor, keyboard and mouse)
• At least 1 chair
• Tidy patch panel (especially if you patch to PC's and telephones in the office)
• Good lighting

You might want to place a small shelf near the entrance to put a pair of these

_{(source: a-chainsaw.com)}

In my experience, the ideal server room will have the following:

• Large enough to house your cabinet or rack. You should have at least 4 ft. of walking space in front and back, ideally all around. If you can get away with it, plan for the possibility of a second rack in the future.
• Secured. You don't necessarily need an armed guard, but at least a good lock. A biometric or card swipe is always good. Home depot has locks that use touch pads so you can assign codes to unlock the door.
• Usually, the server room is also the telco's entry point (demarc), so you'll have your T1 smartjack's there, your PBX or phone system, etc. We usually dedicate one wall and put up plywood so telco's and providers can mount their equipment.
• Air conditioning is a given. You need to keep the room at around 65 - 75 degrees. A dedicated thermostat is preferred since you don't want the A/C to be shut off in the server room on weekends or at nights.
• Power is extremely important. Since your rack is most likely in the middle of the room, you will have cables going across the floor to reach the outlet if they are wall based. If you can have the outlets put on the floor, that's best. If you can't, use some cable covers to avoid tripping over wires. Get dedicated circuits put in for a clean line of electricity. Make sure you have extra outlets on all walls, in a pinch, having access to an outlet can be critical, especially if you need to plug in a laptop or other device.
• Keep a small cabinet or shelves where you can store manuals, cables, spare cards, drives, etc. You want this in an easy to access place during installations and troubleshooting. Keep this out of the way in the room, but accessible.
• Cable management is critical as well, both in the rack and from the plywood wall. Over time it gets very easy to just plug cables in. If the cable management is there, it's easier to keep things organized and label/mark both ends of all wires, the last thing you want to do is trace wires when your network is down.
• For the cabinet itself make sure you have adequate UPS's, cabinet cable management, a good KVM, a 1U slide-out keyboard/mouse/LCD to save on rack space and plenty of ventilation. Cabinet design is a whole dissertation in of itself!
• If the room is closed off, make sure you have proper ventilation for air flow. You'll need some kind of intake vent so hot air can escape. If needed, use a fan to suck the air out. For fresh air, you can put a vent on the door.
• Definitely a phone near the cabinet with a list of support numbers, "911" contacts, etc.
• If I can, I try to have a place to hook up a laptop close by so you can access tools, test against another working system, test client software, etc.
• And there's nothing wrong with a chair for when you are waiting on hold for that tech support rep to come back on the line :)

There's a lot that can go into a server room, if you can get away with a lot of this, your life as an admin will be so much better. The easier it is to get to equipment, trace the setup and get your problems solved, the more effective you can be. Good luck!

I was just watching the film 'Eagle Eye' - apparently the perfect server room involves covering the walls with oddly-coloured fishbowls, which talk via infrared (???) to your main 'CPU', which itself moves around on a robotic arm with a glowing 'eye' set into the middle. Oh and build the whole thing over a large body of water too, this will help in some way ;)

Look at everything from a risk management point of view and everything will fall into place.

• Physical security: What is at risk if a malicious (or ignorant) individual gains access to the server and network hardware? Who will have the permission to enter? Server hardening required? (disable removable drive bootup, BIOS password, disable USB, etc.)
• Climate control: 5 servers and 30 PCs won't make incredible heat in, say, a 20x20 room, but that's a bit much if you're stuffing it in a coat closet. Running at elevated temperatures and/or humidity will shorten the life of your hardware and lead to data loss and expensive replacements. Consider simple ventilation with a dehumidifier or possibly A/C system sized for your needs.
• Business continuity: Battery backup? Data redundancy? Fault tolerant LAN/WAN connections? Any single points of failure in your infrastructure? Do you have enough excess power to run your infrastructure and not blow a fuse if someone plugs in a vacuum cleaner?
• Growth: Have a contingency plan in place for when management demands you double, nay, triple your infrastructure. How will all the critical dependencies scale?

In addition to Techboy's excellent list:

• Toolbox including cable tester, screw drivers, pliers, hex keys and anything required for rack installations, including shifting spanners and the like.
• Cordless phone - with speaker phone if such a beast exists
• Trolley for moving servers
• Ladders/steps/stepladders for working at top of racks and ceiling mounted cable runs
• Consider trolley with lift for installing servers near the top of racks, especially if you have strict OH&S regulations or just care about your workers.
• Hearing protection - we're required to wear it in our DC and they supply disposable ear plugs.
• Power points outside the racks so you can plug in laptops etc easily without disturbing in rack power.
• SNMP or other remote controlled power rails
• Power rails on each side of a rack should go to a different dist panel so that work can be done without losing power to both power supplies in your servers
• Video cameras for additional security
• A row of hooks in a secure place either in or near the DC so that people who work in there regularly can leave a jacket
• Storage for spares, blanking plates, cables and the like
• Possibly spares - especially if your vendor(s) can be persuaded to provide you with common spares in advance of warranty claims/failures (some vendors/re-sellers under some circumstances will provide you with say a couple of hard drives and power supplies. They belong to the vendor, but you can use them if you have a failure and worry about the paper work after the fact.)

From what I am reading here most people are going for massive over kill. You have 5 server and 30 work stations, so since this is a small company by the sounds of it I very much doubt the boss/owner will spring for a biometric scanner, pass card scanner and video system as some examples unless you already have these and it would be a cheap add on for the server room.

So I did one almost the same as what you had, 20 workstations & 8 servers.

Here is what I found went well and was a good cost on the typical limited budget of a small company.

• Phone or at least a phone jack where you can move a phone in should you have to call tech support while in front of the physical server
• A/C, even with 8 server my room temp was about 31 degrees Celsius. For this since the room was in the center of the building and new duct work was out of the question we got one of the portable room ones and exhausted it into the office on the side of the wall closest to the cold air return for the building a/c unit. This worked well and dropped the temp to about 23 degrees but it does take up a lot of space but is really good.
• Don't bother with a rack mount monitor/KVM, I can think of better things to spend $1k on.
  • Get a monitor and a 10 ft VGA cable. Have a table or wall mounted shelf next to the servers, any modern rack mounted server has found mounted VGA port
  • Get a wireless keyboard/mouse that use the same dongle. Just move the VGA cable and wireless dongle to the computer you need access too. Since you will be accessing everything remotely 90% of the time its not a big deal to do it this way
  • If you can get a rack and use rack mounted servers, BUT make sure you get rails that allow the server to be slid out should you need to access the hardware rather then one then needs to be unbolted
  • If you can't get a rack, go to home depot and get the heavy duty freestanding utility shelves, this will work just as well for desktop units
  • Lock, a key or keypad one is fine, you'll have to give a key and the combo to your boss or owner anyway, make sure the servers log who logs into them and it doesn't matter as much who is in the room.
  • If the phone gear is there use the plywood on the wall idea
  • Put the phones on their own power souce UPS
  • Get a UPS that is expandable for the servers
  • Get a UPS that has load banks you can remotely switch off should you need to kill server remotely (Tripplight has these, saved me a few times when I had a wonkly server that would lock up and needed the power killed) Make sure you set the bios to power on after a power outage for all servers. The UPS will only have a few plugs so you have to put your critical servers on it, for me it was a DC/GC and email, this allowed me to reboot those if they crashed
  • Some shelves for parts and the other "stuff" you'll be required to keep in there by the boss (lol unless you are the boss)
  • Dedicated power for the A/C
  • Dedicated power for the Phones
  • Dedicated power for the servers I had a totally of 6 15amp circuits in mine, plus the lights
  • Make any patch cables custom and have them as short as they can be, this will have keep it organized so you don't have them dangling everywhere.
  • If you cannot put it on the second floor, put all the servers on the top rack and work your way down. mine was on the second floor so not an issue for me.

This is what I had in mine, network wiring, etc was all labeled and well organized as well, how that setup is dependent on where it comes in.

Biggest things, keep it organized, and make sure you have room to expand for future growth.

Sterile Environment Is A Must, you must have acceptable flooring, don't even go near carpet as it collects dust. Typically i would opt for raised flooring, is a good option as it's easy to run cable.

Don't Skimp On Cheap Data Racks, with a good cable management system, run one side data and the other power, as some countries regulations don't allow mixing data and power.

The NOC

Above left: The submarine engines used for backup power. Above right: Another view of the power equipment.

Above: This map shows the layout of the data center.

Link to original article

Think about DR planning from the get-go. If I had it to do all over again, I'd have separated the network gear (switches and routers) from the servers, and had a shorter (30u is great) so I could have just rolled the rack out the door and onto a truck that time when Verizon couldn't replace a backhoed T1 line for FOUR FREAKING DAYS and we had to move the servers to our DR location. (Not that I'm still bitter.) Also, depending on location, it's a good idea to have at least one 208 or 240V circuit and space to put the spot cooler when a hurricane knocks out your HVAC in August in Texas.