Home / server / Questions / 612933
Accepted
Daniel W.
Asked: 2014-07-17 02:19:28 +0800 CST

External drive switching from /dev/sda to /dev/sdb

  • 772

We have a small box with external drives attached for backing up configuration sets. I found out the problem is simply that on reboot or whatever unknown event the drive switches from /dev/sda1 to /dev/sdb1.

How can I circumvent this or configure fstab to try both locations?

/dev/sda1       /stor           ext4    defaults,noatime,noexec  0       0

You can see I did quite some debugging:

root@nsa:~# mount /stor
mount: special device /dev/sda1 does not exist

As you can see below I did quite some debugging while writing the question.

syslog:

Jul 16 09:48:48 nsa kernel: [167416.395274] EXT4-fs warning (device sda1): 
         __ext4_read_dirblock:908: error reading directory block (ino 2, block 0)

#df -h before umount:

/dev/sda1       1.4T  185G  1.1T  15% /stor

#dmesg:

[   170.431715] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[119366.019470] usb 1-1.2: USB disconnect, device number 4
[119366.297601] usb 1-1.2: new high-speed USB device number 6 using dwc_otg
[119366.398979] usb 1-1.2: New USB device found, idVendor=1058, idProduct=1021
[119366.399013] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[119366.399029] usb 1-1.2: Product: Ext HDD 1021
[119366.399047] usb 1-1.2: Manufacturer: Western Digital
[119366.399063] usb 1-1.2: SerialNumber: 5743415A4132343133343334
[119366.400719] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[119366.403826] scsi1 : usb-storage 1-1.2:1.0
[119367.398875] scsi 1:0:0:0: Direct-Access     WD       Ext HDD 1021     2002 PQ: 0 ANSI: 4
[119367.401608] sd 1:0:0:0: Attached scsi generic sg0 type 0
[119367.402505] sd 1:0:0:0: [sdb] 2930272256 512-byte logical blocks: (1.50 TB/1.36 TiB)
[119367.403524] sd 1:0:0:0: [sdb] Test WP failed, assume Write Enabled
[119367.404593] sd 1:0:0:0: [sdb] Asking for cache data failed
[119367.404623] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[119367.407157] sd 1:0:0:0: [sdb] Test WP failed, assume Write Enabled
[119367.410142] sd 1:0:0:0: [sdb] Asking for cache data failed
[119367.410185] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[119374.143786]  sdb: sdb1
[119374.146995] sd 1:0:0:0: [sdb] Test WP failed, assume Write Enabled
[119374.149166] sd 1:0:0:0: [sdb] Asking for cache data failed
[119374.149203] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[119374.149231] sd 1:0:0:0: [sdb] Attached SCSI disk
[153689.349544] EXT4-fs error (device sda1): ext4_find_entry:1309: inode #2: comm rsync: reading directory lblock 0

#lsusb:

Bus 001 Device 006: ID 1058:1021 Western Digital Technologies, Inc. Elements 2TB
hard-drive

1 Answers

  1. Best Answer

    As has been mentioned in the comments, grab the disk's UUID and stick this in your fstab;

    UUID=66a7ba58-b1e2-4d91-9b5e-085064a954ab /stor ext4 defaults 0 0

    (replace the UUID value with that of your own). As simple ls -la /dev/disk/by-uuid (which is just a collection of symlinks named the UUID of the disk which point to the real device's identifer (sda, sdb, etc). In my case;

    lrwxrwxrwx 1 root root 9 Jul 7 08:45 66a7ba58-b1e2-4d91-9b5e-085064a954ab -> ../../sdf

    The disk with that UUID is /dev/sdf, but I don't have to know that. The device's location could, will, and does change. It's UUID is baked into the filesystem's table of contents, which will never change unless you format it clean.

    • 9