Questions[vmware-esxi](server)

An SD (SDHC) card installed in an HP ProLiant DL380p Gen8 server running VMware ESXi just failed :(

I encountered some ominous looking messages on the vCenter console and in the HP ProLiant ILO event log...

Lost connectivity to the device ... backing the boot filesystem. As a result, host configuration changes will not be saved to persistent storage.

Embedded Flash/SD-CARD: Error writing media 0, physical block 848880: Stack Exception.

VMware advocates the use of USB and SD (SDHC) boot devices for ESXi. It was one of the main reasons the smaller footprint ESXi was developed (versus the older ESX). I've spent much time highlighting the differences between ESXi's installable and embedded modes to coworkers and clients. However, these failures do seem to happen. In this case, this is my third instance.

Luckily, this is a vSphere cluster with SAN storage. What steps should be taken to remediate this failure?

This seems basic, but I'm confused about the patching strategy involved with manually updating standalone VMware ESXi hosts. The VMware vSphere blog attempts to explain this, but the actual process is still not clear to me.

From the blog:
Say Patch01 includes updates for the following VIBs: "esxi-base", "driver10" and "driver 44". And then later Patch02 comes out with updates to "esxi-base", "driver20" and "driver 44". P2 is cumulative in that the "esxi-base" and "driver44" VIBs will include the updates in Patch01. However, it's important to note that Patch02 not include the "driver 10" VIB as that module was not updated.

This VMware Communities post gives a different answer. This one contradicts the other.

Many of the ESXi installations I encounter are standalone and do not utilize Update Manager. It is possible to update an individual host using the patches make available through the VMWare patch download portal. The process is quite simple, so that part makes sense.

The bigger issue is determining what exactly to actually download and install. In my case, I have a good number of HP-specific ESXi builds that incorporate sensors and management for HP ProLiant hardware.

• Let's say that those servers start with an ESXi build #474610 from 9/2011.
• Looking at the patch portal screenshot below, there is a patch for ESXi update01, build #623860. There are also patches for builds #653509 and #702118.
• Coming an old version of ESXi (e.g. vendor-specific build), what is the proper approach to bring the system fully up-to-date? Which patches are cumulative and which need to be applied sequentially? Is installing the newest build the right approach, or do I need to step back and patch incrementally?
• Another consideration is the large size of the patch downloads. At sites with limited bandwidth, downloading of multiple ~300mb patches is difficult.

I have Suse Linux 12.1 and i am trying to mount a single RAID 1 disk, to explore the files in it. However when mounting it:

 # mount /dev/sdc1 /mnt/test
  mount: unknown filesystem type 'linux_raid_member' 

I started reading around and many advised to just force the filessystem type

  # mount -t ext4 /dev/sdc1 /mnt/test
  mount: /dev/sdc1 already mounted or /mnt/test busy

when trying

 umount /dev/sdc1                 
 umount: /dev/sdc1: not mounted

Could someone provide some advise?

I am running my machines insed an ESXI server and it is a virtual disk. However this should not play, as this disks are not used by any other machines

thaknks!

I'm experiencing fsync latencies of around five seconds on NFS datastores in ESXi, triggered by certain VMs. I suspect this might be caused by VMs using NCQ/TCQ, as this does not happen with virtual IDE drives.

This can be reproduced using fsync-tester (by Ted Ts'o) and ioping. For example using a Grml live system with a 8GB disk:

Linux 2.6.33-grml64:
root@dynip211 /mnt/sda # ./fsync-tester
fsync time: 5.0391
fsync time: 5.0438
fsync time: 5.0300
fsync time: 0.0231
fsync time: 0.0243
fsync time: 5.0382
fsync time: 5.0400
[... goes on like this ...]

That is 5 seconds, not milliseconds. This is even creating IO-latencies on a different VM running on the same host and datastore:

root@grml /mnt/sda/ioping-0.5 # ./ioping -i 0.3 -p 20 .
4096 bytes from . (reiserfs /dev/sda): request=1 time=7.2 ms
4096 bytes from . (reiserfs /dev/sda): request=2 time=0.9 ms
4096 bytes from . (reiserfs /dev/sda): request=3 time=0.9 ms
4096 bytes from . (reiserfs /dev/sda): request=4 time=0.9 ms
4096 bytes from . (reiserfs /dev/sda): request=5 time=4809.0 ms
4096 bytes from . (reiserfs /dev/sda): request=6 time=1.0 ms
4096 bytes from . (reiserfs /dev/sda): request=7 time=1.2 ms
4096 bytes from . (reiserfs /dev/sda): request=8 time=1.1 ms
4096 bytes from . (reiserfs /dev/sda): request=9 time=1.3 ms
4096 bytes from . (reiserfs /dev/sda): request=10 time=1.2 ms
4096 bytes from . (reiserfs /dev/sda): request=11 time=1.0 ms
4096 bytes from . (reiserfs /dev/sda): request=12 time=4950.0 ms

When I move the first VM to local storage it looks perfectly normal:

root@dynip211 /mnt/sda # ./fsync-tester
fsync time: 0.0191
fsync time: 0.0201
fsync time: 0.0203
fsync time: 0.0206
fsync time: 0.0192
fsync time: 0.0231
fsync time: 0.0201
[... tried that for one hour: no spike ...]

Things I've tried that made no difference:

• Tested several ESXi Builds: 381591, 348481, 260247
• Tested on different hardware, different Intel and AMD boxes
• Tested with different NFS servers, all show the same behavior:
  • OpenIndiana b147 (ZFS sync always or disabled: no difference)
  • OpenIndiana b148 (ZFS sync always or disabled: no difference)
  • Linux 2.6.32 (sync or async: no difference)
  • It makes no difference if the NFS server is on the same machine (as a virtual storage appliance) or on a different host

Guest OS tested, showing problems:

• Windows 7 64 Bit (using CrystalDiskMark, latency spikes happen mostly during preparing phase)
• Linux 2.6.32 (fsync-tester + ioping)
• Linux 2.6.38 (fsync-tester + ioping)

I could not reproduce this problem on Linux 2.6.18 VMs.

Another workaround is to use virtual IDE disks (vs SCSI/SAS), but that is limiting performance and the number of drives per VM.

Update 2011-06-30:

The latency spikes seem to happen more often if the application writes in multiple small blocks before fsync. For example fsync-tester does this (strace output):

pwrite(3, "aaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaa"..., 1048576, 0) = 1048576
fsync(3)                                = 0

ioping does this while preparing the file:

[lots of pwrites]
pwrite(3, "********************************"..., 4096, 1036288) = 4096
pwrite(3, "********************************"..., 4096, 1040384) = 4096
pwrite(3, "********************************"..., 4096, 1044480) = 4096
fsync(3)                                = 0

The setup phase of ioping almost always hangs, while fsync-tester sometimes works fine. Is someone capable of updating fsync-tester to write multiple small blocks? My C skills suck ;)

Update 2011-07-02:

This problem does not occur with iSCSI. I tried this with the OpenIndiana COMSTAR iSCSI server. But iSCSI does not give you easy access to the VMDK files so you can move them between hosts with snapshots and rsync.

Update 2011-07-06:

This is part of a wireshark capture, captured by a third VM on the same vSwitch. This all happens on the same host, no physical network involved.

I've started ioping around time 20. There were no packets sent until the five second delay was over:

No.  Time        Source                Destination           Protocol Info
1082 16.164096   192.168.250.10        192.168.250.20        NFS      V3 WRITE Call (Reply In 1085), FH:0x3eb56466 Offset:0 Len:84 FILE_SYNC
1083 16.164112   192.168.250.10        192.168.250.20        NFS      V3 WRITE Call (Reply In 1086), FH:0x3eb56f66 Offset:0 Len:84 FILE_SYNC
1084 16.166060   192.168.250.20        192.168.250.10        TCP      nfs > iclcnet-locate [ACK] Seq=445 Ack=1057 Win=32806 Len=0 TSV=432016 TSER=769110
1085 16.167678   192.168.250.20        192.168.250.10        NFS      V3 WRITE Reply (Call In 1082) Len:84 FILE_SYNC
1086 16.168280   192.168.250.20        192.168.250.10        NFS      V3 WRITE Reply (Call In 1083) Len:84 FILE_SYNC
1087 16.168417   192.168.250.10        192.168.250.20        TCP      iclcnet-locate > nfs [ACK] Seq=1057 Ack=773 Win=4163 Len=0 TSV=769110 TSER=432016
1088 23.163028   192.168.250.10        192.168.250.20        NFS      V3 GETATTR Call (Reply In 1089), FH:0x0bb04963
1089 23.164541   192.168.250.20        192.168.250.10        NFS      V3 GETATTR Reply (Call In 1088)  Directory mode:0777 uid:0 gid:0
1090 23.274252   192.168.250.10        192.168.250.20        TCP      iclcnet-locate > nfs [ACK] Seq=1185 Ack=889 Win=4163 Len=0 TSV=769821 TSER=432716
1091 24.924188   192.168.250.10        192.168.250.20        RPC      Continuation
1092 24.924210   192.168.250.10        192.168.250.20        RPC      Continuation
1093 24.924216   192.168.250.10        192.168.250.20        RPC      Continuation
1094 24.924225   192.168.250.10        192.168.250.20        RPC      Continuation
1095 24.924555   192.168.250.20        192.168.250.10        TCP      nfs > iclcnet_svinfo [ACK] Seq=6893 Ack=1118613 Win=32625 Len=0 TSV=432892 TSER=769986
1096 24.924626   192.168.250.10        192.168.250.20        RPC      Continuation
1097 24.924635   192.168.250.10        192.168.250.20        RPC      Continuation
1098 24.924643   192.168.250.10        192.168.250.20        RPC      Continuation
1099 24.924649   192.168.250.10        192.168.250.20        RPC      Continuation
1100 24.924653   192.168.250.10        192.168.250.20        RPC      Continuation

2nd Update 2011-07-06:

There seems to be some influence from TCP window sizes. I was not able to reproduce this problem using FreeNAS (based on FreeBSD) as a NFS server. The wireshark captures showed TCP window updates to 29127 bytes in regular intervals. I did not see them with OpenIndiana, which uses larger window sizes by default.

I can no longer reproduce this problem if I set the following options in OpenIndiana and restart the NFS server:

ndd -set /dev/tcp tcp_recv_hiwat 8192 # default is 128000
ndd -set /dev/tcp tcp_max_buf 1048575 # default is 1048576

But this kills performance: Writing from /dev/zero to a file with dd_rescue goes from 170MB/s to 80MB/s.

Update 2011-07-07:

I've uploaded this tcpdump capture (can be analyzed with wireshark). In this case 192.168.250.2 is the NFS server (OpenIndiana b148) and 192.168.250.10 is the ESXi host.

Things I've tested during this capture:

Started "ioping -w 5 -i 0.2 ." at time 30, 5 second hang in setup, completed at time 40.

Started "ioping -w 5 -i 0.2 ." at time 60, 5 second hang in setup, completed at time 70.

Started "fsync-tester" at time 90, with the following output, stopped at time 120:

fsync time: 0.0248
fsync time: 5.0197
fsync time: 5.0287
fsync time: 5.0242
fsync time: 5.0225
fsync time: 0.0209

2nd Update 2011-07-07:

Tested another NFS server VM, this time NexentaStor 3.0.5 community edition: Shows the same problems.

Update 2011-07-31:

I can also reproduce this problem on the new ESXi build 4.1.0.433742.

I have imported a VM into an ESXi server using the VMware "Converter stand alone utility". However, this process is a little tedious. Since I eventually want several copies of this VM (or, to be more accurate, several more-or-less identical instances of this VM) to be running at the same time, is there a way to clone the already imported VM? Or do I have to re-import for each instance I want?