Home / server / Questions / 545379
In Process
Mark L
Asked: 2013-10-12 04:36:56 +0800 CST

Docker will only bind forwarded ports to IPv6 interfaces

  • 772

Is there a way I can tell docker to only bind forwarded ports to IPv4 interfaces?

I have a machine running on Digital Ocean with IPv6 disabled:

# echo '1' > /proc/sys/net/ipv6/conf/lo/disable_ipv6  
# echo '1' > /proc/sys/net/ipv6/conf/lo/disable_ipv6  
# echo '1' > /proc/sys/net/ipv6/conf/all/disable_ipv6  
# echo '1' > /proc/sys/net/ipv6/conf/default/disable_ipv6
# /etc/init.d/networking restart

ifconfig reports there are no IPv6-enabled interfaces:

# ifconfig
docker0   Link encap:Ethernet  HWaddr 00:00:00:00:00:00  
          inet addr:172.17.42.1  Bcast:0.0.0.0  Mask:255.255.0.0
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:1372 errors:0 dropped:0 overruns:0 frame:0
          TX packets:7221 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:88091 (88.0 KB)  TX bytes:10655750 (10.6 MB)

eth0      Link encap:Ethernet  HWaddr 04:01:08:c1:b1:01  
          inet addr:198.XXX.XXX.XXX  Bcast:198.199.90.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:97602 errors:0 dropped:4 overruns:0 frame:0
          TX packets:15362 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:141867997 (141.8 MB)  TX bytes:1376970 (1.3 MB)

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

lxcbr0    Link encap:Ethernet  HWaddr 9e:51:04:ed:13:d4  
          inet addr:10.0.3.1  Bcast:10.0.3.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

When I launch a new docker container and ask it to port forward 8000 to 8000 in the container it does so only on IPv6 interfaces. Is there a way to make it only bind to IPv4 interfaces?

# docker run -p 8000:8000 -i -t colinsurprenant/ubuntu-raring-amd64 /bin/bash

# lsof -OnP | grep LISTEN
sshd      1275             root    3u     IPv4 ... TCP *:22 (LISTEN)
sshd      1275             root    4u     IPv6 ... TCP *:22 (LISTEN)
dnsmasq   2975      lxc-dnsmasq    7u     IPv4 ... TCP 10.0.3.1:53 (LISTEN)
docker    9629             root    7u     IPv6 ... TCP *:8000 (LISTEN)
docker    9629 9630        root    7u     IPv6 ... TCP *:8000 (LISTEN)
docker    9629 9631        root    7u     IPv6 ... TCP *:8000 (LISTEN)
docker    9629 9632        root    7u     IPv6 ... TCP *:8000 (LISTEN)
docker    9629 9633        root    7u     IPv6 ... TCP *:8000 (LISTEN)
docker    9629 9634        root    7u     IPv6 ... TCP *:8000 (LISTEN)
docker    9629 9698        root    7u     IPv6 ... TCP *:8000 (LISTEN)
linux

2 Answers

  1. I ran through the same issue:

    Edit /etc/modprobe.d/blacklist.conf with:

    blacklist ipv6

    And /etc/default/grub with:

    GRUB_CMDLINE_LINUX_DEFAULT="ipv6.disable=1 console=ttyS0"

    Then update-grub and reboot.

    • 3

  2. Actually, docker uses the netfilter firewall to make sure the service is available. lsof wouldn't tell you anything. Try running

    iptables -L -t nat
ip6tables -L -t nat

    It is possible that the container doesn't listen to the specified port however.

    You can look into your container to make sure your service is listening to the expected ports using nsenter:

    nsenter --net -t PID netstat -ltpn

    PID must be the PID of a process running inside the container, most probably your service. --net is to enter the network namespace. Then the netstat options -ltpn is to list listening (-l) TCP (-t) sockets. Show the process (-p), and show port numbers in numeric format (-n).

    • 1