Robert's questions

I'm trying to get an IPv6 enabled router to forward data from one interface to the other and I'm having issues.

When following this example (http://www.cisco.com/en/US/tech/tk872/technologies_configuration_example09186a0080ba6106.shtml) I am able to get full connectivity between all 3 routers in my simulator. However when I try to use only 1 router; I can't get connectivity to the other interfacs on the same router.

My PC is directly attached to FA 1/0 and it can ping the router's interface. However it can not ping any other interface on the router(which unless I'm missing something it should be able to do). The router on the other hand can ping everything. I thought static routes might help; but the router already has routes for everything.

I'm thinking the packet should come in; router looks up the destination in it's ipv6 routing table and then realizes it's for itself, and should respond. I thought maybe it couldn't respond directly; so I tried pinging a device like 2001:0000:0000:1000::2, but i don't get a response.

I'm running on IOS 12.4.

I'm missing something(hopefully simple), but I just can't see what it is. With only 1 router; how do I enable my PC to talk to the other subnets? Thank you in advance, Robert

Topology:

R1

FA 0/0:
2001:0000:0000:0000::1/52

FA 0/1:
2001:0000:0000:1000::1/52

FA 1/0:
2001:0000:0000:2000::1/52

Loopback 0:
2001:0000:0000:3000::1/52

PC:
2001:0000:0000:2000::2/52

PC plugs directly into FA 1/0 on the router.

--- Configuration ---

ipv6 cef
ipv6 unicast routing

interface Loopback0
 no ip address
 ipv6 address 2001:0000:0000:3000::1/52
 ipv6 enable
!
interface FastEthernet0/0
 no ip address
 duplex auto
 speed auto
 ipv6 address 2001:0000:0000::1/52
 ipv6 enable
!
interface FastEthernet0/1
 no ip address
 duplex auto
 speed auto
 ipv6 address 2001:0000:0000:1000::1/52
 ipv6 enable
!
interface FastEthernet1/0
 no ip address
 duplex auto
 speed auto
 ipv6 address 2001:0000:0000:2000::1/52
 ipv6 enable

--- end of config ---

--- routing table ---

IPV6Lab#show ipv6 route
IPv6 Routing Table - 10 entries
Codes: C - Connected, L - Local, S - Static, R - RIP, B - BGP
       U - Per-user Static route
       I1 - ISIS L1, I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary
       O - OSPF intra, OI - OSPF inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
       ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2

C   2001:0000:0000::/52 [0/0]
     via ::, FastEthernet0/0

L   2001:0000:0000::1/128 [0/0]
     via ::, FastEthernet0/0

C   2001:0000:0000:1000::/52 [0/0]
     via ::, FastEthernet0/1

L   2001:0000:0000:1000::1/128 [0/0]
     via ::, FastEthernet0/1

C   2001:0000:0000:2000::/52 [0/0]
     via ::, FastEthernet1/0

L   2001:0000:0000:2000::1/128 [0/0]
     via ::, FastEthernet1/0

C   2001:0000:0000:3000::/52 [0/0]
     via ::, Loopback0

L   2001:0000:0000:3000::1/128 [0/0]
     via ::, Loopback0

L   FE80::/10 [0/0]
     via ::, Null0

L   FF00::/8 [0/0]
     via ::, Null0

--- end of routing table ---

Edit: Fixed problem description to indicate my Pc is on FA 1/0; not FA 0/1. Thank you for pointing out the error Celada.

How do I have multiple vlans (tagged) go over one NIC in server 2008 R2? I know it's possible in *nix and I know how to do that on the network side. But it doesn't help if the server 2008 R2 can't understand that.

I am looking for a card-reader solution that includes not only the physical card-reader but a method to read/program the cards. The end goal is have to give my end users a card-reader and then an associated card they need to swipe to login to the windows machine. I am not worried about end-users 'swapping' cards as they are geographically distant.

Suggestions on where to start?

Thanks in advance,

I'm looking to set our WINS servers via GPO, is that possible? We have 2 SSID which our clients can connect to (one which connects to a DHCP we control, the other to a different DHCP we don't - each with their own WINS).

We do a lot of mapping via DFS so that's why we need our wins servers.

Help?

I've got 300+ win7 clients I need to deploy WPA2 Personal PSK on. I can use a GPO to deploy the SSID information on the clients which is good but not the PSK. Is there a clean/easy way to script it so the PSK can be entered on the machines?

If possible I don't want to give the PSK to the end users.

I'm looking for a solution to get graphics from a tablet to a projector wirelessly. The idea is to have the professor connect to the the solution and then connect to a network share, load their powerpoint/video/content and then output their screen to the projector while being able to walk around the room during class.

We have been using a solution called 'AirProjector' which went out of business several years back. Major downfall of of the AirProjector was video is very choppy. The more screen the device had to update the slower and poorer the display was to the point where animation was taboo.

Any suggestions on a solution to the above? Even if we dont' gain full motion video maintaning the level of service would be nice. This change is required as we are moving from an open wireless network to requireing WPA2 Personal(we don't have the time to dedicate to getting WPA2 Enterprise up right now) and the device only supports WEP at best.

So I want deploy a WPA2-Personal SSID that our managed clients will already have the network settings setup for(windows vista and windows 7 x64). I also want to deploy the network configuration via gpo so I can avoid touching the hundrids of machines. However I can't find how to make the gpo take the PSK. I've read articles saying that GPOs can't do that but I havn't found any way to manually add the network config in via scirpt or anything like that.

Ideas?

So I'm running OCS 2007 R2 Enterprise. We currently have one pool with one server in it. When we brought out a consultant he was emphatic that we needed a director server. So we brought it up but didn't have time to fully intigrate it to the envrioment. He left and now that I have time to research the stuff I think I he's wrong.

My understanding is that a director routes between multiple pools, so if a user logs in and is on pool A, he'll go to pool A and not pool B. To scale a pool incase of performance issues a hardware loadbalancer is required(which is what we were concerned about).

So if my above understanding is correct, why have multiple pools? Is there somewhere that cleanly explains this?

Thanks,

I'm trying to deploy an policy for the compatabilty list in IE 8 though at this point I'd settle for just being able to use a .admx

The basic problem I'm running into is when creating/editing a GPO I can't view .admx files but I can view/import .adm files. I get the error message inetres.admx is not a valid template file. Only files that end with the .admx file extension can be added to this Group Poilcy Object.

I am running two 2008 SP1 DCs, with a functional level of 2008. MMC version 3.0, and the group policy editor has features like 'filter' and 'preferences' so it's a quite recent version(though I don't know the exact version). We have a central store setup under C:\Windows\SYSVOL\domain\Policies\PolicyDefinitions\ on our DCs. I have tried creating a new GPO from scratch incase some settings were ported over from the 2003 domain level.

Everything seems like it should be more than ready but for some reason it's failing. I'm hoping it's something pretty basic but it's not obvious to me. Help?

[edits for spelling]

Currently I have a two domain enviroment of vista with all machines calling into WSUS. The with the recent advent of IE8 being avaliable through WSUS that's been great. However I want to stop IE8 from being adverstied and for the life of me I can't find it in WSUS. There are plenty of blocker tool kits out there but they are regestry settings on the local machine and sadly my enviorment is large enough that going and touching each machine(darn you UAC!) is unfeasable at best.

Has anyone been able to stop WSUS from advertising IE8 and can point me in the direction of how to do this?

Thank you in advance