the title of this question might be confusing. So my issue is I have registered a domain in Godaddy, and setup the business gmail using that domain. Recently I decided to migrate the DNS from Godaddy to AWS Route53, and I still want my business email to work as usual.

There are some MX records and TXT records already exist in Godaddy's DNS management page for email and domain verification, do I need to put those records in the AWS Route53? Do I need to verify the domain again since the domain host is changed from Godaddy to AWS?

I installed Hadoop on one Azure VM, and it works fine by using its OS disk. However, I attached one hard disk to my VM, and I want to know how to configure Hadoop to only use this new hard disk as its default storage disk. Can anyone tell me how to change the configurations?

Any Help would be grateful. Thank You.

I recently captured one azure vm image in one storage account, and planning to migrate this image to another storage account under a different subscription. I used PowerShell Script to run this task, but I came across with this problem: The storage account was not found. And one more concern is that PowerShell has to be related to the specific Azure Account, otherwise it can not run script. So the story is how to use PowerShell control different subscriptions at the same time, and also perform the migration task?? Thank You.

BTW, the PowerShell script is shown below:

Change these to match the source account

$sourceStorageAccountName = "" $sourceContainerName = "" $sourceStorageKey = "" #Need this if moving data from a different subscription

Destination Account Information

$destStorageAccountName = Read-Host "Enter Destination Storage Account Name" $destStorageAccountKey = Get-AzureStorageKey $destStorageAccountName | %{$_.Primary} $destContainerName = Read-Host "Enter Destination Container Name"

$sourceContext = New-AzureStorageContext -StorageAccountName $sourceStorageAccountName -StorageAccountKey $sourceStorageKey -Protocol Http $destContext = New-AzureStorageContext -StorageAccountName $destStorageAccountName -StorageAccountKey $destStorageAccountKey

$uri = $sourceContext.BlobEndPoint + $sourceContainerName +"/"

Copy Operation

Get-AzureStorageBlob -Context $sourceContext -Container $sourceContainerName | ForEach-Object { Start-AzureStorageBlobCopy -SrcUri "$uri$($_.Name)" -DestContext $destContext -DestContainer $destContainerName -DestBlob "hackathon/$($_.Name)" }

Checking Status of Blob Copy -- This can be commented out if no confirmation is needed

Get-AzureStorageBlob -Context $sourceContext -Container $sourceContainerName | ForEach-Object { Get-AzureStorageBlobCopyState -Blob $_.Name -Context $destContext -Container $destContainerName -WaitForComplete }

The problem is like this: Get-AzureStorageKey : No current subscription has been designated. Use Select-AzureSubscription -Current to set the current subscription.

I created one VM with 100G SSD, but it's only D rive, which is the temporary disk. I want to attach another SSD drive to the VM, but I'm not sure its type. Is is possible to do this? Thank You

I created one Nginx with one Linux Azure VM, is it possible to make nginx listen to different ports so that when I change the port number, the content would be different. I found there would be a collision if I created two or more ports related to HTTP on VM. Can anyone help me with that?

I created one html file under one user file, and I want Nginx to serve this html file. But the website always show the default one. I am new to Nginx, I want someone help me with this.

Any help would be grateful, I really want some help with that. Thank You

The Nginx configuration is just like the default:

I couldn't find any clue about this error. Can anyone help me? Any help would be grateful. Thank You.

I'm trying to use Powershell scripts to start multiple VMs at the same time. I only know how to start one single VM or all VMs at the same time, but in my case, I only want to make change to selected VMs. Can anyone help me with that? Any help would be grateful. Thank You

I am considering about two cases. One is edit runbooks on Visual Studio, then execute them to perform Automation task directly. Another one is that edit runbooks on Visual Studio, then I use PowerShell to execute those runbooks. I'm not sure about these two options. Can anyone help me? Any help would be grateful. Thank You

Actually I want to run these runbooks by myself, not relying on Automation Part. In this case, I can choose when to deploy them, and also it is flexible for me to choose variables. It would be better to have some simple tutorials for me. Any Help would be grateful. Thank You

I am testing a runbook on Automation, but it was suspended. The details show : The job action 'Activate' cannot be run, because the process stopped unexpectedly. The job action was attempted 3 times. I want to know how to solve this problem. Thank You

I'm trying to find a way to clone the image of one VM on Azure. I knew some information about 'sysprep' and Linux system, but those require delete the previous VM. In my case, I don't want to delete the previous VM because I want to keep it working as usual. it's just like copy and paste one file, file name is different but it has the same content. There are no collisions between the previous VM and the new VM. Both VM can work individually.

Any help would be grateful. Thank You.